The summer is over, it seems. I've been home for weeks. The NBI course is over.
After finishing the Community Design/Build class, I was done with all my Yestermorrow responsibilities. I hung around for a few days so I could have some last minute fun with my intern and NBI friends, and then headed off on a multi-day Amtrak ride.
It was hard to leave. I had grown so attached to the place and people. I loved the balance of work and play. The whole place seemed healthy and I was always happy. I learned a lot about tools, design and construction over the summer, gained a lot of great contacts for future opportunities, and made great friends who I hope to see again.
Since I've been home, I've been talking about Yestermorrow nonstop. I miss waking up early in the morning to do a morning chore routine. I miss having communal breakfast, lunch and dinner. I miss morning meetings, identifying tasks that need to be done and having the means to do them. There was a sense of belonging and purpose that I haven't experienced to that extent anywhere else.
If there is one word to summarize how I feel about Yestermorrow now, I would have to say "grateful." I am so thankful to my school for funding me this summer, the Yestermorrow staff for allowing me to come be a "mystic," and the interns for accepting me as one of them and teaching me a plethora of skills. I cannot vocalize how much this summer has positively affected me, but I do recognize it and am grateful.
It's been an amazing summer. Thanks.
Saturday, August 22, 2009
Sunday, August 9, 2009
The End of Design/Build
We finished, with time and money to spare.
For the last couple days of construction, we generally split into three groups: those on the roof, those working on siding and those finishing the benches. I was on the siding crew.
We used four inch (rough cut, so not 4 inches exactly - lots of variation) pine with two inch spaces in between.
When it was time to round the corner, we had to find pieces that were similar widths so that we could line our corners up properly.
The benches were covered in six inch cedar with an 8th inch gap. It took a lot of time to get all the covering on, mostly because the bench frame pieces didn't line up perfectly and needed to be corrected.
The roof was four inch pine with a two inch spacing covered in corregated plastic. Our instructors had used these materials in a previous Community D/B class so we got to see an example beforehand. There's metal flashing around the edges.
The girls who built the table installed it. There was a little more wobble than we were comfortable with, so we added another leg to the front quickly.
The finished building:
Group shots, at the celebration.
We had a graduation ceremony at Dave Seller's Temple, where we had to walk to the receiving line (made up of our instructors, Dave, several of their old friends and some interns) through the flying sparks from a too-big fire to be handed our graduation certificates that Dave found necessary to burn the edges of. It was the perfect way to end my last day of work in Vermont.
Overall, I'm very proud of the work that was done in class. We designed and built a fairly large structure in two weeks. It looks great and we had good responses from the clients. It's very comfortable and well lit - it's cozy. It's easy to see out and is oriented well, so parents can watch their children in comfort. I made a lot of great friends who all seemed to leave in good spirits. I loved my instructors thoroughly. I am absolutely thrilled that I got to participate in this class.
For the last couple days of construction, we generally split into three groups: those on the roof, those working on siding and those finishing the benches. I was on the siding crew.
We used four inch (rough cut, so not 4 inches exactly - lots of variation) pine with two inch spaces in between.
When it was time to round the corner, we had to find pieces that were similar widths so that we could line our corners up properly.
The benches were covered in six inch cedar with an 8th inch gap. It took a lot of time to get all the covering on, mostly because the bench frame pieces didn't line up perfectly and needed to be corrected.The roof was four inch pine with a two inch spacing covered in corregated plastic. Our instructors had used these materials in a previous Community D/B class so we got to see an example beforehand. There's metal flashing around the edges.
The girls who built the table installed it. There was a little more wobble than we were comfortable with, so we added another leg to the front quickly.
The finished building:
Group shots, at the celebration.
We had a graduation ceremony at Dave Seller's Temple, where we had to walk to the receiving line (made up of our instructors, Dave, several of their old friends and some interns) through the flying sparks from a too-big fire to be handed our graduation certificates that Dave found necessary to burn the edges of. It was the perfect way to end my last day of work in Vermont.Overall, I'm very proud of the work that was done in class. We designed and built a fairly large structure in two weeks. It looks great and we had good responses from the clients. It's very comfortable and well lit - it's cozy. It's easy to see out and is oriented well, so parents can watch their children in comfort. I made a lot of great friends who all seemed to leave in good spirits. I loved my instructors thoroughly. I am absolutely thrilled that I got to participate in this class.
Wednesday, August 5, 2009
So Rewarding
Today was an exciting day for the Community D/B class. We moved our structure out to the site,
raised it,
and added some roofing and decking details.
There were a few hiccups - the main one being the bench pieces not fitting exactly into place when rearranging. It was such a rewarding day, to finally see the structure in it's spot. It fits well on the site, looks nice with the trees in the background, and corresponds to the individual porches very well.
I spent the majority of the day on the roof - there were five of us up there and the structure held well (although we did add a little bracing on the overhang so we didn't accidentally build a warp into the roof.) This gives me confidence for the structure's capability to withstand Vermont snow-loads.
Tomorrow, more roof and bench work, and hopefully the installation of the table.
raised it,
and added some roofing and decking details.
There were a few hiccups - the main one being the bench pieces not fitting exactly into place when rearranging. It was such a rewarding day, to finally see the structure in it's spot. It fits well on the site, looks nice with the trees in the background, and corresponds to the individual porches very well. I spent the majority of the day on the roof - there were five of us up there and the structure held well (although we did add a little bracing on the overhang so we didn't accidentally build a warp into the roof.) This gives me confidence for the structure's capability to withstand Vermont snow-loads.
Tomorrow, more roof and bench work, and hopefully the installation of the table.
Tuesday, August 4, 2009
Design/Build, Fast!
We finished building our model. It is possibly the best model I have ever made.
(Or, mostly finished.) The back three trusses gained some posts on the front end of the building to provide extra support and create a nook for the people at the table. We decided to square off the building for decking's sake.
When we make changes to the plans, a little masking tape holds the new onto the old. It creates a little flip book of sorts. I am amused by this.
Most of the students in my class are in or have completed grad school with an architecture degree. Therefore, when it's time to draw something, I'm not generally the most qualified. However, I have been helping with the revisions. I've never used a drafting table before - pretty helpful, really. (I am, however, one of the go-to folks on the work site, at times.)
After adding the new supports to the trusses, we raised them.
Before doing so, we had to level and build the deck. We built it on skids, but we don't plan on the skids being used for pulling. The ground is too soft at the site for a vehicle to drive on it, so we've had to design the building in pieces. The joists have been placed, but only with a few bolts (and no screws.)
We got all the trusses up.
This fellow and I worked together to design and build the benches. This was the first support completed. We used sandwiching techniques similar to those that we used on the trusses, as well as the only vertical supports in the structure. The benches are attached to the floor joists only, so we can take the trusses off for transportation.
After installing supports to each truss, we had to build similar supports for the truss-less floor joists. These intermediate joists each got the seat, back rest and upper shelf. The light support on the left is one of these structures. (We painted the structure with a very watered down black paint - it's enough to disguise wood discoloration/inconsistencies, but still show wood grain.)
I spent this afternoon and evening working with three other ladies from my class to build the table for the structure. We used 1 by 5 cedar, the same that is being used for decking.
In this picture, we were testing out the sizing of the table compared with the benches. The far side rests on a beam that I installed on the farthest truss, while the front of the table is supported by a leg. I didn't get an adequate photo of the bottom of the table to show all the supports that we installed to keep that leg firm. While we used dozens of screws on the bottom, we managed to keep the top hardware free. We were very proud.
We even signed our names.
While we were building our table, decking was set.
As we were putting finishing touches on, the structure was disassembled. Tomorrow morning, we get to move the pieces out to the site.
Some unmentioned thoughts and highlights from the last several days:
- Jim, Bill and I had to measure the bridge between here and our site. There is no clearance sign, for some odd reason. The bridge is very narrow, so the rush of running out to the lowest point, climbing high enough to get the tape measure to the top and reading numbers was quite extreme. Lots of fun and giggling afterwords. Had the bridge been a little lower, there would not be giggling.
- My arm looks like it has some sort of skin disease because of all the thin black paint that has made its way onto me instead of the structure.
- Every morning, Steve leads the class in a clap - starting slow and getting faster until there are enthusiastic whoops and lots of smiles. For some reason, this works for making us energetic.
- We have been working every evening after dinner. Thursday evening and Sunday were the only times we've had off before dark since the class started. I am amazingly tired, but in such a wonderful way. Building this structure is mentally and physically exhausting, but very rewarding. It changes so quickly. I am amazed at how much we have done in such a short amount of time.
- The instructors are great. They are full of encouragement and good ideas. At times, their non-stop ideas can be frustrating - significant changes were still being made in the late stages of design. Sometimes, when someone has just figured out all the details of their next move, prepared and possible even started, one or three of the instructors will swoop in with entirely different suggestions. The timing is not always the best, but they have great suggestions.
I am heading home a week from today.
(Or, mostly finished.) The back three trusses gained some posts on the front end of the building to provide extra support and create a nook for the people at the table. We decided to square off the building for decking's sake.
When we make changes to the plans, a little masking tape holds the new onto the old. It creates a little flip book of sorts. I am amused by this.Most of the students in my class are in or have completed grad school with an architecture degree. Therefore, when it's time to draw something, I'm not generally the most qualified. However, I have been helping with the revisions. I've never used a drafting table before - pretty helpful, really. (I am, however, one of the go-to folks on the work site, at times.)
After adding the new supports to the trusses, we raised them.
Before doing so, we had to level and build the deck. We built it on skids, but we don't plan on the skids being used for pulling. The ground is too soft at the site for a vehicle to drive on it, so we've had to design the building in pieces. The joists have been placed, but only with a few bolts (and no screws.)
We got all the trusses up.
This fellow and I worked together to design and build the benches. This was the first support completed. We used sandwiching techniques similar to those that we used on the trusses, as well as the only vertical supports in the structure. The benches are attached to the floor joists only, so we can take the trusses off for transportation.
After installing supports to each truss, we had to build similar supports for the truss-less floor joists. These intermediate joists each got the seat, back rest and upper shelf. The light support on the left is one of these structures. (We painted the structure with a very watered down black paint - it's enough to disguise wood discoloration/inconsistencies, but still show wood grain.)I spent this afternoon and evening working with three other ladies from my class to build the table for the structure. We used 1 by 5 cedar, the same that is being used for decking.
In this picture, we were testing out the sizing of the table compared with the benches. The far side rests on a beam that I installed on the farthest truss, while the front of the table is supported by a leg. I didn't get an adequate photo of the bottom of the table to show all the supports that we installed to keep that leg firm. While we used dozens of screws on the bottom, we managed to keep the top hardware free. We were very proud.
We even signed our names.While we were building our table, decking was set.
As we were putting finishing touches on, the structure was disassembled. Tomorrow morning, we get to move the pieces out to the site.Some unmentioned thoughts and highlights from the last several days:
- Jim, Bill and I had to measure the bridge between here and our site. There is no clearance sign, for some odd reason. The bridge is very narrow, so the rush of running out to the lowest point, climbing high enough to get the tape measure to the top and reading numbers was quite extreme. Lots of fun and giggling afterwords. Had the bridge been a little lower, there would not be giggling.
- My arm looks like it has some sort of skin disease because of all the thin black paint that has made its way onto me instead of the structure.
- Every morning, Steve leads the class in a clap - starting slow and getting faster until there are enthusiastic whoops and lots of smiles. For some reason, this works for making us energetic.
- We have been working every evening after dinner. Thursday evening and Sunday were the only times we've had off before dark since the class started. I am amazingly tired, but in such a wonderful way. Building this structure is mentally and physically exhausting, but very rewarding. It changes so quickly. I am amazed at how much we have done in such a short amount of time.
- The instructors are great. They are full of encouragement and good ideas. At times, their non-stop ideas can be frustrating - significant changes were still being made in the late stages of design. Sometimes, when someone has just figured out all the details of their next move, prepared and possible even started, one or three of the instructors will swoop in with entirely different suggestions. The timing is not always the best, but they have great suggestions.
I am heading home a week from today.
Subscribe to:
Posts (Atom)
Posts
